APC 40 Knob for Davinci Resolve

  • Q&A Forum
  • [RESOLVED] APC 40 Knob for Davinci Resolve
0
0

Hello,

I didn’t found a solution in other threads so I hope you can help me.

I’m looking for a right/left mapping for a single knob on my APC 40.

Output should be mouse movement right/left that I can size masks in Davinci Resolve

I know that velocity is 0-127 but I don’t find the right rule.

 

RESOLVED
Marked as spam
Posted by (Q&A Forum: 1, Answers: 2)
May 1, 2017 11:04 am
555 views
0
Private answer

Hello,

Used 6 translators to solve the problem with APC 40 (1) First Version.

T1:

I:MIDI B8 14 oo

Rule:

if g0==1 then exit rules, skip Outgoing Action
g0=1

Outgoing:

Left mouse button down at 27,847

T2:

I:MIDI B8 14 oo

Rule:

if oo==0 then exit rules, skip Outgoing Action
if oo<ga then exit rules, skip Outgoing Action

O:Mouse move -2(up)

 

T3:

I: MIDI B8 14 oo

Rule:

if oo==127 then exit rules, skip Outgoing Action
if oo>ga then exit rules, skip Outgoing Action

O:Mouse move 2 (down)

T4

I: MIDI B8 14 00

Rule: ga=oo

O: none

T5:

MIDI B8 14 oo

Rule: –

O: One-shot timer “Knob1_time”: 200 ms delay

T6:

I: On timer “Knob1_timer”

Rule: g0=0

O: left mouse button up

 

Hope it helps…

 

 

 

 

 

 

Marked as spam
Posted by (Q&A Forum: 1, Answers: 2)
February 25, 2018 4:53 pm
0
Private answer

Hi info55,

please check this thread and you will find the answer to your issue. All you need to do is to replace the outgoing  key commands to “Left” and “Right” instead of Shift-A, Shift-Z and of course the incoming MIDI need to be set to whatever your APC is sending.

http://www.bome.com/forums/viewtopic.php?f=3&t=2844

Cheers

 

Marked as spam
Posted by (Q&A Forum: 1, Answers: 8)
May 1, 2017 2:39 pm
Hi, I’ve checked this out and got following result: If I turn the knob right, mouse will move into right corner. If I turn knob left after Position B0 15 7F, oo=0x7F, mouse will move into the right corner again until I have reached B0 15 16, oo=0x16. Then mouse movement goes to the left side. But I want to have a directly response (left/right) Can you help me please ? Thanks.
( at May 1, 2017 10:27 pm)

I’m not clear on what you are looking for. You want to control mouse movement with a knob? This is entirely possible, however there would probably need to be step adjustment depending on resolution of the screen.
For instance if the width of the screen is 1920 and the values of knob (midi values) is 0-127 you would have to move 15 pixels per one change in knob value.

The translator would look something like this
Incoming controller (pick the controller you want) on channel (pick the channel you want) set velocity to pp
Rule
pp = pp*15
Outgoing
Set X position to absolute value pp

This should give you an idea.

( at May 2, 2017 1:23 am)

Did you ever resolve this? What knob were you wanting to use and if your APC40 MKii or standard APC40?

( at February 24, 2018 4:58 am)